• You need to be a registered member of Barbel Fishing World to post on these forums. Some of the forums are hidden from non-members. Please refer to the instructions on the ‘Register’ page for details of how to join the new incarnation of BFW...

J W Young River Specialist issue

Neil Blood

Senior Member & Supporter
I’m curious if anyone has had similar issues with this pin or any ideas.

With heritage Young's pins, the centre screw has a habit of loosening, resulting in too much play between the drum and backplate. Normally a micro adjustment with a tiny screwdriver remedies the issue.

On the above pin, I’ve had it around 12 months. There’s always been a bit too much play as described. Problem is I cant adjust the screw as its locked tight. Therefore cant adjust it either way. Dont want to try and over force it and wreck the head of the small screw.

Any ideas please, or is next stop get in touch with Young’s?
 
It seems that various makers of centrepins go through phases of using threadlock on float screws.
I've no doubt it saves them some problems, but I wish they wouldn't do it. However, I can understand why they might want to.
I'd ask Young's how to proceed, especially if you have warranty remaining.
 
Just checked my own River Specialist and I cannot turn the grub screw either. As with Neil I don't want to try too hard for fear of damaging it.
There is a very small amount of movement, just a mm or two when pulling on the drum away from the backplate but not enough to concern me.
I had the same situation with a couple of reels made by Dave Beale (now passed) who informed me he always used loctite once he had the play correct, therefore it could never be adjusted. In fact my DB Aerial Longcast has a bit more movement than the River Specialist but again not enough to cause me any concern.
 
Thanks for checking Mike, looks like the screw is being fixed with loctite as standard then on this reel.

Its not a massive amount of play between drum and backplate, its just something I’ve always been able to adjust myself on other Youngs and Mill Tackle reels.
 
Neil. I have no play on mine. I'm reluctant to fiddle with it if you don't mind.
I had a problem with the ratchet on mine. Chris sorted it no trouble. I would definitely recommend you contact him at Youngs at he will get it right for you.
 
When they were in Redditch we always used to give the grub screw threads a light tap with a hammer to initially make them tighter to screw in, then a bit of Green thread lock too. The play was set by us to be as minimal as possible and then QC by Jim before he signed off the certificates.

They would have been pretty tight leaving the factory back then to prevent them backing off themselves and making the spool play excessive.
 
As far as I know young’s use loctite on the end float on all their reels. They say they are set up perfectly at the factory and don’t require altering. Obviously that’s not always the case.

I have altered them in the past by breaking the loctite seal, removing the screw, cleaning them up and putting it back in dry.

The loctite they use isn’t a particularly strong one, it’s designed to be removed.
I’m not saying go ahead as I don’t want my good name being flamed if it goes south, but I am saying it was fine when I did and if you do go ahead you must not try and tighten it, you need to remove it first and clean the threads.

You need a very good fitting screwdriver and apply a reasonable downward pressure as you attempt to unscrew it and it should come out. That’s how young’s would remove it if they needed too as well.

If you send it back to Chris just ask him if he could put your grub screw back in dry so you can make your own tweaks
 
Last edited:
My Young's BJ had quite a lot of play straight out of the box, which I sorted with a slight adjustment of the screw.
Other Young's I've bought have been fine , so it appears some do slip through a bit slack.
 
Just a little aside on loctite. Many years ago(40+) I bought the rsm a triumph dolomite she had seen and fallen in love with. Only a year old, said OK, when it arrived staggered to see it was an auto. Just out of warranty ofcourse but I felt 2nd was missing. Took it in for adjustment and told needed a new auto box. Agreed, took it in the main dealers. Got a call to say engine and gearbox could not be separated as the factory at that time was using loctite on engine bolts.
Choice was taking a chance with ali block and gearbox case or not.
Thats when she got her new chevette.
 
When I got my Triton a few years ago I didn’t know the grub screw had Loctite. I knackered it and had to send it back and ask Chris to sort it out (which he kindly did). I can understand a fixed screw on a bearing reel where the “play” on the spool is basically giving the illusion of a true-pin reel, but fixing the screw on a true-pin is daft as far as I’m concerned; the need to adjust the grub screw is basic to the proper running of those reels.
 
Neil, if you apply some heat to the screw, the Loctite should soften and enable you to unscrew it. I think a soldering iron would do the trick.
Failing that, give Chris a shout at JWYOUNGS, or you could contact Gary Mills. I know Jim had an issue with him, but I've always found him to be a very sound and helpful chap.
You might find that once you get the reel play set to your liking, the screw may move and constantly require a tweak, so if that happens, you are as well using a tiny bit of superglue or the blue thread lock and apply it with a needle to the very top threads. I did that on a reel myself after having a chat with Gary Mills.
Best of luck 👍
 
Back
Top